Skip to content
← All posts Engineering

10 design rules for injection-molded parts

A part that prints perfectly can still fail in a mold. These are the ten rules we check before any design goes to a toolmaker.

Sergio FloresFounder, Flores Engineering8 min read
Injection-molded consumer product shown in six colorways

Injection molding makes plastic parts cheap at volume, but the steel tool is expensive and slow to change. Every fix after the tool is cut costs money and weeks. Good design for manufacturing (DFM) catches problems while they are still a CAD change.

These rules apply to most thermoplastics. Your molder will have specifics for your material, so treat them as a starting checklist, not a substitute for their review.

1. Keep walls uniform

Plastic shrinks as it cools. Thick sections cool slower than thin ones, which causes sink marks, warping and voids. Pick a nominal wall, often 1.5 to 3 mm for small consumer parts, and hold it everywhere you can. Where thickness must change, transition gradually.

2. Add draft to every vertical face

Draft is a slight taper that lets the part release from the mold. One to two degrees is a common starting point. Textured surfaces need more, because the texture grips the steel.

3. Size ribs to the wall

Ribs add stiffness without thick walls. Keep rib thickness at about 50 to 60% of the wall it attaches to, or the rib will cause a sink mark on the opposite face. Ribs also need draft.

4. Core out thick features

If a feature looks solid in CAD, hollow it out and support it with ribs. Solid blocks of plastic are the most common cause of sink and long cycle times.

5. Design bosses carefully

Screw bosses should connect to nearby walls with ribs instead of standing alone, and their walls should follow the same thickness rule. Check the screw manufacturer's recommended hole size for your material.

6. Round the inside corners

Sharp inside corners concentrate stress and block plastic flow. An inside radius of at least half the wall thickness, with an outside radius equal to the inside radius plus the wall, keeps the wall uniform around the corner.

7. Avoid undercuts when you can

An undercut is any feature that stops the part from pulling straight out of the mold: a side hole, a snap hook, a groove. Each one needs a slide or lifter in the tool, which adds cost and maintenance. Often a small change, like a pass-through core, removes the undercut entirely.

8. Think about where the plastic goes in

The gate is where plastic enters the part. It leaves a small mark, and where flow fronts meet you get weld lines. Talk to your molder early about gate location so marks and weld lines land on hidden or low-stress surfaces.

9. Leave room for ejector pins

Ejector pins push the part out of the mold and leave small round marks. Give them flat areas on non-cosmetic faces, and expect them on the inside of housings.

10. Tolerance only what matters

Molded parts shrink, and different materials shrink differently. Tight tolerances everywhere drive up tool cost and rejected parts. Call out the critical dimensions, like mating features and bearing fits, and let the rest follow the molder's standard tolerances.

Prototype before you cut steel

We prototype molded parts with SLA and FDM prints first, so fit, assembly and feel are proven before tooling. Printed parts will not show every molding issue, so a DFM review with the molder is still the final check before the tool is released.

Heading to tooling?

Send your CAD and we will review it for moldability before you commit to steel.
Get a free estimate

More from the blog

Row of FDM 3D printers in the Flores Engineering lab in Kearny, NJPrototyping · 7 min read

FDM vs SLA vs CNC: which prototype process should you use?

A practical guide to choosing FDM 3D printing, SLA resin printing or CNC machining for prototypes, with real prices, lead times and design rules from our NJ lab.

Resin 3D printer in the Flores Engineering labManufacturing · 5 min read

How to get a 3D printed part quoted fast (and what files to send)

What to include when you ask for a 3D printing or CNC quote: file formats, units, quantity, material and deadlines. A checklist from our NJ prototype lab.